Furman M-8S Power Conditioner with Sequencer

$311.14
PA SKU # FUR M8S MFR # M-8S UPC # 654061041078
  • Support Lifetime Tech Support
  • Best Seller Best Seller!
  • Question Ask a Question
Only 1 Left! — In Stock & Ready to Ship Order now! Limited quantity in stock! Most orders placed before 3pm MST ship same day (except weekends and holidays).
  • Product Highlights
  • Power Sequencing
  • Noise Filtration
  • Surge Protection
  • 9 Total Outlets
  • 15 Amp Rating
  • Protection OK Indicator
  • Wall Wart Spacing
Only 1 Left! — In Stock & Ready to Ship Order now! Limited quantity in stock! Most orders placed before 3pm MST ship same day (except weekends and holidays).

15 Amp Standard Power Conditioner with Sequencer

Install an M-8S in your rack, and the eight outlets in the rear panel will power up in sequence and protect all your equipment up to a 15-amp load.

Merit M-8S Power Sequencer is the perfect low-cost AC power solution for any rack mount system where power sequencing is desired.

Install an M-8s in to the top slot of your rack, and the six delayed outlets in the rear panel will power up sequentially and protect all your equipment up to a 15-amp load.

Includes 3 delayed outlet banks - each with 2 outlets - plus 2 unswitched outlets.
  • Power Sequencing
  • Prevents excessive inrush currents.
  • Six sequenced rear panel outlets (in three groups), two unswitched rear panel outlets, and one front panel unswitched outlet.
  • Momentary and maintained sequencing via rear panel terminal block or front panel switch (momentary only).
  • Noise Filtration
  • Noise filtering to reduce radio frequency and electromagnetic interference.
  • Surge Protection
  • Ensures equipment stays safe.
  • 9 Total Outlets
  • Eight rear panel outlets and one front panel convenience panel outlet.
  • 15 Amp Rating
  • 15 amp rating, with circuit breaker.
  • "Protection OK" Indicator
  • Front panel indicator LEDs for Outlet Banks, Protection OK and Power Status.
  • Wall Wart Spacing
  • Rear outlets have been spaced to accommodate even the bulkiest of wall warts and adapters.
  • All settings and configurations available on rear panel.
  • Maximum Output Current: 15 amps, 120 VAC (thermal breaker)
  • Line Cord: 14 AWGx3, 10 feet, black, fixed, NEMA 5-15P plug
  • AC Receptacles:
    Convenience Outlet (Front Panel): 1 un-switched NEMA 15-5R
    Rear Panel Outlets: 2 un-switched NEMA 5-15R (1 duplex)
    6 Sequenced Outlets: NEMA 5-15R (3 duplexes, each controlled by separate relay)
  • AC Surge Protection: Merit class (sacrificial)
  • Protection Modes: Line to neutral, zero ground leakage (spike protection)
  • Operating Voltage: 130 V RMS (max continuous)
  • Max Clamp Voltage: 500 V peak
  • Peak Impulse Current: 12,000 amps
  • Energy Rating: 225 joules
  • Filtering: Standard level Pi LCR filter (AC)
  • Noise Attenuation: > 26 dB, 100 kHz to 1 MHz
  • Operating Temperature Range: 5 C (40 F) to 40º C (105º F)
  • Humidity Range: < 90% rH (relative humidity)
  • Switch: Front panel, sequence (ON, OFF)
  • Circuit Breaker: Front panel, push to reset (thermal)
  • Front Panel Indicators: Delay 1, delay 2, delay 3, power, protection OK
  • Dip Switches: 12V Mode on/off, GND mode on, momentary/maintained (rear panel)
  • Potentiometer: Rear panel, time calibration fine tune delay adjust
  • Remote Terminal: +5-30 VDC In, 12 VDC (12 mA) out
  • Phoenix type 4-pin connector with screw terminals; +12V, STAT, REM, GND (class 2 wiring)
  • Dimensions: 19.00 x 8.75 x 1.75" (482.60 x 222.30 x 44.50 mm)
  • Weight: 7.00 lb (3.18 kg)
  • Furman Merit M-8S Power Sequencer
  • Limited 3-Year Warranty